Turbo manifold for NA6 with T25 flange

by **rhysmate** » Thu, 15 Mar 2012 4:27 +0000

by **Steve** » Thu, 15 Mar 2012 9:54 +0000

If you don't get one through here, I had one made by Abe in Artech, absolute gent to deal with + great quality.
http://www.artechfabrication.com/index.php

Steve

by **mx5ideways** » Thu, 15 Mar 2012 10:15 +0000

Steve wrote:If you don't get one through here, I had one made by Abe in Artech, absolute gent to deal with + great quality.
http://www.artechfabrication.com/index.php

Steve

That's where I got my downpipe too Rhys, he does great work, go for it :wink:

by **rhysmate** » Fri, 16 Mar 2012 9:02 +0000

if you dont mind me asking.... what kind of money did you pay lads?

by **rhysmate** » Fri, 16 Mar 2012 10:10 +0000

think this is any good??

http://www.ebay.com/itm/89-97-Turbo-Man ... 5516wt_954

by **Steve** » Fri, 16 Mar 2012 12:19 +0000

Worth reading this thread, it links to a very similar (same?) manifold.
http://www.miataturbo.net/showthread.php?t=60200
ETD : http://www.protegegarage.com/600-product-600.html

I got a few quotes at the time for 2 GReddy manifold alternatives :
The ETD manifold was 449usd + 110usd shipping
Artech 325usd + 65usd shipping

by **twail** » Fri, 16 Mar 2012 12:25 +0000

Theres cheap cast ones on ebay, i have one on mine, with no issues at all!

You'll have to chop off the flange and put on a t25 one though

by **rhysmate** » Fri, 16 Mar 2012 1:38 +0000

ill probably go down the cheaper route and buy ebay spec

its gonna be a cheapish build im not looking for crazy power and im only gonna run 7-8 psi.. i can do the fabrication of the t25 flange easy enough or just buy a stainless t25 mani like the one above.. thanks lads.. looking forward to building it.. especially when theres help aroung the place

by **rhysmate** » Fri, 16 Mar 2012 2:25 +0000

twail wrote:Theres cheap cast ones on ebay, i have one on mine, with no issues at all!

You'll have to chop off the flange and put on a t25 one though

did you chop the flange off or make a bracket?

by **twail** » Sat, 17 Mar 2012 12:01 +0000

I chopped it and welded on a new one.

It does the job fine, and I have a t28 at .8 bar

by **rhysmate** » Sat, 17 Mar 2012 6:55 +0000

twail wrote:I chopped it and welded on a new one.

It does the job fine, and I have a t28 at .8 bar

Any chance you have a pic of it after you did so I can see what I must do??

Turbo manifold for NA6 with T25 flange

Turbo manifold for NA6 with T25 flange

Re: Turbo manifold for NA6 with T25 flange

Re: Turbo manifold for NA6 with T25 flange

Re: Turbo manifold for NA6 with T25 flange

Re: Turbo manifold for NA6 with T25 flange

Re: Turbo manifold for NA6 with T25 flange

Re: Turbo manifold for NA6 with T25 flange

Re: Turbo manifold for NA6 with T25 flange

Re: Turbo manifold for NA6 with T25 flange

Re: Turbo manifold for NA6 with T25 flange

Re: Turbo manifold for NA6 with T25 flange

Who is online


	Board index ‹ Other bits and pieces ‹ Wanted Change font size Print view


	Author Message Turbo manifold for NA6 with T25 flange by rhysmate » Thu, 15 Mar 2012 4:27 +0000 Turbo manifold for NA6 with T25 flange bend the rules............rule the bends --Turbo Mx5 Build Thread Of Epic Power-- rhysmate ** Posts: 862 Joined: Thu, 16 Jun 2011 4:17 +0000 Location: CORK Top Re: Turbo manifold for NA6 with T25 flange by Steve » Thu, 15 Mar 2012 9:54 +0000 If you don't get one through here, I had one made by Abe in Artech, absolute gent to deal with + great quality. http://www.artechfabrication.com/index.php Steve Steve Site Admin Posts: 5529 Joined: Wed, 05 Mar 2008 10:16 +0000 Top Re: Turbo manifold for NA6 with T25 flange by mx5ideways » Thu, 15 Mar 2012 10:15 +0000 Steve wrote:If you don't get one through here, I had one made by Abe in Artech, absolute gent to deal with + great quality. http://www.artechfabrication.com/index.php Steve That's where I got my downpipe too Rhys, he does great work, go for it 1990 Eunos Roadster 1.6: cusco coilovers, carbing front and rear strut braces, 1.8 brakes, performance engine and diff mounts, stage 2 cerametalic 6 puck 1.8 clutch with lightweight JUN 1.8 flywheel, 1.8 LSD, GReddy manifold, Garrett T25 turbo, ARTech down pipe, E-Manage blue ecu, Altezza injectors, FMIC. Zoom engineering center console, carbon fibre bonnet, garage vary front lip, lightweight garage hundred one hardtop, carbing 6 pt cage. 1999 mx5 1.8 RS: XYZ drift spec Coilovers, reversed Ssr dori dori mesh wheels, wide arches, custom bonnet with s15 vent, rx8 spoiler, carbon rx7 sideskirts, full Arc induction kit, heated electric leather rx8 seats. mx5ideways Posts: 523 Joined: Mon, 13 Aug 2007 7:36 +0000 Location: cork/limerick YIM Top Re: Turbo manifold for NA6 with T25 flange by rhysmate » Fri, 16 Mar 2012 9:02 +0000 if you dont mind me asking.... what kind of money did you pay lads? bend the rules............rule the bends --Turbo Mx5 Build Thread Of Epic Power-- rhysmate Posts: 862 Joined: Thu, 16 Jun 2011 4:17 +0000 Location: CORK Top Re: Turbo manifold for NA6 with T25 flange by rhysmate » Fri, 16 Mar 2012 10:10 +0000 think this is any good?? http://www.ebay.com/itm/89-97-Turbo-Man ... 5516wt_954 bend the rules............rule the bends --Turbo Mx5 Build Thread Of Epic Power-- rhysmate Posts: 862 Joined: Thu, 16 Jun 2011 4:17 +0000 Location: CORK Top Re: Turbo manifold for NA6 with T25 flange by Steve » Fri, 16 Mar 2012 12:19 +0000 Worth reading this thread, it links to a very similar (same?) manifold. http://www.miataturbo.net/showthread.php?t=60200 ETD : http://www.protegegarage.com/600-product-600.html I got a few quotes at the time for 2 GReddy manifold alternatives : The ETD manifold was 449usd + 110usd shipping Artech 325usd + 65usd shipping Steve Site Admin Posts: 5529 Joined: Wed, 05 Mar 2008 10:16 +0000 Top Re: Turbo manifold for NA6 with T25 flange by twail » Fri, 16 Mar 2012 12:25 +0000 Theres cheap cast ones on ebay, i have one on mine, with no issues at all! You'll have to chop off the flange and put on a t25 one though twail * Posts: 107 Joined: Tue, 20 Oct 2009 11:52 +0000 Top Re: Turbo manifold for NA6 with T25 flange by rhysmate » Fri, 16 Mar 2012 1:38 +0000 ill probably go down the cheaper route and buy ebay spec its gonna be a cheapish build im not looking for crazy power and im only gonna run 7-8 psi.. i can do the fabrication of the t25 flange easy enough or just buy a stainless t25 mani like the one above.. thanks lads.. looking forward to building it.. especially when theres help aroung the place bend the rules............rule the bends --Turbo Mx5 Build Thread Of Epic Power-- rhysmate ** Posts: 862 Joined: Thu, 16 Jun 2011 4:17 +0000 Location: CORK Top Re: Turbo manifold for NA6 with T25 flange by rhysmate » Fri, 16 Mar 2012 2:25 +0000 twail wrote:Theres cheap cast ones on ebay, i have one on mine, with no issues at all! You'll have to chop off the flange and put on a t25 one though did you chop the flange off or make a bracket? bend the rules............rule the bends --Turbo Mx5 Build Thread Of Epic Power-- rhysmate Posts: 862 Joined: Thu, 16 Jun 2011 4:17 +0000 Location: CORK Top Re: Turbo manifold for NA6 with T25 flange by twail » Sat, 17 Mar 2012 12:01 +0000 I chopped it and welded on a new one. It does the job fine, and I have a t28 at .8 bar twail * Posts: 107 Joined: Tue, 20 Oct 2009 11:52 +0000 Top Re: Turbo manifold for NA6 with T25 flange by rhysmate » Sat, 17 Mar 2012 6:55 +0000 twail wrote:I chopped it and welded on a new one. It does the job fine, and I have a t28 at .8 bar Any chance you have a pic of it after you did so I can see what I must do?? bend the rules............rule the bends --Turbo Mx5 Build Thread Of Epic Power-- rhysmate ** Posts: 862 Joined: Thu, 16 Jun 2011 4:17 +0000 Location:** CORK Top


	Who is online Users browsing this forum: No registered users and 3 guests


	Board index The team • Delete all board cookies • All times are UTC [ DST ]